[Documentation] [TitleIndex] [WordIndex] 

Contents

  1. Usage
  2. Nodes
    1. face_detection
    2. face_tracking
    3. face_detection_cuda
    4. face_detection_dlib
    5. face_listener
    6. Changing Node settings
  3. Additional Setup Information
    1. Multi-threading:
    2. OpenCV CUDA:
    3. Dlib

Usage

These ROS nodes are designed to detect and track faces in images coming from a ROS image topic. The nodes display or publish an image with the resulting detections drawn on top of the image. The coordinates of the detections can also be published to a separate topic. The settings of the detection system can be easily adapted using ROS rqt_reconfigure (rosrun rqt_reconfigure rqt_reconfigure). The nodes also publish the coordinates of the faces for the use with other nodes. To work for a wide variaty of scenarios, the following features are included:

An example of some of the nodes can be found here. The code is available on GitHub.

Nodes

face_detection

Node uses OpenCV (HAAR Cascade detector) to detect faces only. 

roslaunch face_detection face_detection.launch

face_tracking

Node uses OpenCV (HAAR Cascade detector) to detect faces. Detected faces are tracked using Opencv (Optical flow LK). Both the detected and the tracked faces are then merged into one list.

face_detection_cuda

Node uses OpenCV (HAAR Cascade detector) and CUDA to detect faces only. 

roslaunch face_detection face_detection_cuda.launch

face_detection_dlib

Node uses Dlib (HOG Cascade detector) to detect faces only. 

roslaunch face_detection face_detection_dlib.launch

face_listener

Example node reading the published face coordinates 

rosrun face_detection face_listener

Changing Node settings

All setting can be adjusted dynamicaly using the ROS rqt reconfigure setup. 

rosrun rqt_reconfigure rqt_reconfigure

Once you have the rqt_reconfigure open, change the input image default (/camera/image_raw) to your desired input. Additional information about the different settings are annotated in the dynamic reconfigure setup (hover over the desired setting in the rqt_reconfigure for additional information)

Additional Setup Information

Multi-threading:

In order to get the best performance out of the detection, you should compile your OpenCV package with Multi-threading support. OpenCV makes use of TBB (WITH_TBB=ON) to to enable Multi-threading, for both versions 2.4 and 3.0. Here is a tutorial on how to install OpenCV with Multi-threading for version 3.0 (http://rodrigoberriel.com/2014/10/installing-opencv-3-0-0-on-ubuntu-14-04/).

WARNING: Reinstalling OpenCV might break some of you other ROS packages, so you might want to stick to your current version. This node will also run without Multi-threading support, but especially the Face_Tracking node will run considerably slower.

OpenCV CUDA:

To enable faster detection, CUDA support has been enabled for the detection process. Keep in mind that the CUDA detection is slightly different to the original OpenCV detection and will deliver different, slightly less accurate results. Currently only the detection process has been implemented for CUDA. The tracking part is still under development.

Dlib

The Dlib face detection system has a higher accuracy to detect faces which are closer to the camera, especially faces which are tilted sideways. The system is a bit slower than OpenCV, mainly because of the lack of additional configuration settings (min max searchwindow_scale ...). It also has a lower accuracy with smaller faces. The detection is using a HOG cascade.

Since it is uncommon to have Dlib installed, the face_detection_dlib node is disabled by default. If you want to use this node, you need to enable it in the CMakeLists file under the section "DLIB". You will also need to link the installation directory in the CMakeLists (include(../dlib/cmake)). The Dlib library can be found on their website (http://dlib.net/). If your CPU does not support the AVX instruction set, you might have to change the line "#set(USE_AVX_INSTRUCTIONS 1)"

2022-05-28 12:35