Show EOL distros:
Package Summary
ROS-Industrial support for the Fanuc CR-35iA (and variants).
This package contains configuration data, 3D models and launch files for Fanuc CR-35iA manipulators. This currently includes the base model only.
Specifications:
- CR-35iA - Normal Range
Joint limits and maximum joint velocities are based on the information in the FANUC Robot CR-35iA Mechanical Unit Operator's Manual version B-83734EN/01. All urdfs are based on the default motion and joint velocity limits, unless noted otherwise (ie: no support for high speed joints, extended / limited motion ranges or other options).
Before using any of the configuration files and / or meshes included in this package, be sure to check they are correct for the particular robot model and configuration you intend to use them with.
Note: there is currently some confusion over the correct values for the joint limits of joints 2 and 3. Version B-83734EN/01 of the Operator's Manual incorrectly states that 1.05 rad equals 120 degrees, and that 0.39 rad equals 45 degrees (joint 2). Additionally, it gives a value of -122.9 degrees for the lower limit of joint 3, whereas (at least) Roboguide Rev K have this limit set to -182 degrees. We advise users to pay extra attention when verifying the xacro in this support package until this is cleared up.
- Maintainer status: developed
- Maintainer: G.A. vd. Hoorn (TU Delft Robotics Institute) <g.a.vanderhoorn AT tudelft DOT nl>
- Author: G.A. vd. Hoorn (TU Delft Robotics Institute)
- License: BSD
- Bug / feature tracker: https://github.com/ros-industrial/fanuc_experimental/issues
- Source: git https://github.com/ros-industrial/fanuc_experimental.git (branch: indigo-devel)
Package Summary
ROS-Industrial support for the Fanuc CR-35iA (and variants).
This package contains configuration data, 3D models and launch files for Fanuc CR-35iA manipulators. This currently includes the base model only.
Specifications:
- CR-35iA - Normal Range
Joint limits and maximum joint velocities are based on the information in the FANUC Robot CR-35iA Mechanical Unit Operator's Manual version B-83734EN/01. All urdfs are based on the default motion and joint velocity limits, unless noted otherwise (ie: no support for high speed joints, extended / limited motion ranges or other options).
Before using any of the configuration files and / or meshes included in this package, be sure to check they are correct for the particular robot model and configuration you intend to use them with.
Note: there is currently some confusion over the correct values for the joint limits of joints 2 and 3. Version B-83734EN/01 of the Operator's Manual incorrectly states that 1.05 rad equals 120 degrees, and that 0.39 rad equals 45 degrees (joint 2). Additionally, it gives a value of -122.9 degrees for the lower limit of joint 3, whereas (at least) Roboguide Rev K have this limit set to -182 degrees. We advise users to pay extra attention when verifying the xacro in this support package until this is cleared up.
- Maintainer status: developed
- Maintainer: G.A. vd. Hoorn (TU Delft Robotics Institute) <g.a.vanderhoorn AT tudelft DOT nl>
- Author: G.A. vd. Hoorn (TU Delft Robotics Institute)
- License: BSD
- Bug / feature tracker: https://github.com/ros-industrial/fanuc_experimental/issues
- Source: git https://github.com/ros-industrial/fanuc_experimental.git (branch: indigo-devel)
Package Summary
ROS-Industrial support for the Fanuc CR-35iA (and variants).
This package contains configuration data, 3D models and launch files for Fanuc CR-35iA manipulators. This currently includes the base model only.
Specifications:
- CR-35iA - Normal Range
Joint limits and maximum joint velocities are based on the information in the FANUC Robot CR-35iA Mechanical Unit Operator's Manual version B-83734EN/01. All urdfs are based on the default motion and joint velocity limits, unless noted otherwise (ie: no support for high speed joints, extended / limited motion ranges or other options).
Before using any of the configuration files and / or meshes included in this package, be sure to check they are correct for the particular robot model and configuration you intend to use them with.
Note: there is currently some confusion over the correct values for the joint limits of joints 2 and 3. Version B-83734EN/01 of the Operator's Manual incorrectly states that 1.05 rad equals 120 degrees, and that 0.39 rad equals 45 degrees (joint 2). Additionally, it gives a value of -122.9 degrees for the lower limit of joint 3, whereas (at least) Roboguide Rev K have this limit set to -182 degrees. We advise users to pay extra attention when verifying the xacro in this support package until this is cleared up.
- Maintainer status: developed
- Maintainer: G.A. vd. Hoorn (TU Delft Robotics Institute) <g.a.vanderhoorn AT tudelft DOT nl>
- Author: G.A. vd. Hoorn (TU Delft Robotics Institute)
- License: BSD
- Bug / feature tracker: https://github.com/ros-industrial/fanuc/issues
- Source: git https://github.com/ros-industrial/fanuc.git (branch: kinetic)
Package Summary
ROS-Industrial support for the Fanuc CR-35iA (and variants).
This package contains configuration data, 3D models and launch files for Fanuc CR-35iA manipulators. This currently includes the base model only.
Specifications:
- CR-35iA - Normal Range
Joint limits and maximum joint velocities are based on the information in the FANUC Robot CR-35iA Mechanical Unit Operator's Manual version B-83734EN/01. All urdfs are based on the default motion and joint velocity limits, unless noted otherwise (ie: no support for high speed joints, extended / limited motion ranges or other options).
Before using any of the configuration files and / or meshes included in this package, be sure to check they are correct for the particular robot model and configuration you intend to use them with.
Note: there is currently some confusion over the correct values for the joint limits of joints 2 and 3. Version B-83734EN/01 of the Operator's Manual incorrectly states that 1.05 rad equals 120 degrees, and that 0.39 rad equals 45 degrees (joint 2). Additionally, it gives a value of -122.9 degrees for the lower limit of joint 3, whereas (at least) Roboguide Rev K have this limit set to -182 degrees. We advise users to pay extra attention when verifying the xacro in this support package until this is cleared up.
- Maintainer status: developed
- Maintainer: G.A. vd. Hoorn (TU Delft Robotics Institute) <g.a.vanderhoorn AT tudelft DOT nl>
- Author: G.A. vd. Hoorn (TU Delft Robotics Institute)
- License: BSD
- Bug / feature tracker: https://github.com/ros-industrial/fanuc/issues
- Source: git https://github.com/ros-industrial/fanuc.git (branch: kinetic)
Overview
This package is part of the ROS-Industrial program. See fanuc for more information.
Installation
See the main fanuc page.
Usage
See the Working With ROS-Industrial Robot Support Packages page.